Indiana > Statewide > Department Of Enviromental Management > Air

OAQ Process Information Application PI-07 Welding And Cutting Of Metal 52547 - Indiana

OAQ Process Information Application PI-07 Welding And Cutting Of Metal Form. This is a Indiana form and can be used in Air Department Of Enviromental Management Statewide .
 Fillable pdf Last Modified 8/25/2010
Get this form for FREE as a print-only pdf

Indiana Department of Environmental Management Office of Air Quality Air Permit Application Page 1 of 3 PI-07 Instructions 5/2006 PROCESS INFORMATION: Welding & Cutting of Metal ­ INSTRUCTIONS Microsoft Word version of PI-07 Adobe PDF version of PI-07 The purpose of PI-07 (state form 52547) is to obtain detailed information about welding and cutting of metal. Complete one form for each process unit (or group of identical process units). PI-07 is a required form for all air permit applications submitted to IDEM, OAQ. For the purposes of this form, the term "source" refers to the plant as a whole and NOT to the individual emissions units. If you do not provide the enough information to adequately describe the process, the application process may be stopped. If you have any questions, contact the Air Permit Reviewer of the Day (PROD) at (317) 233-0178 or 1-800-451-6027 extension 3-0178 (toll free call within Indiana). Part A: Welding Information Part A identifies the welding process. If there are multiple units that are identical in nature, capacity, and use, you may use one row to summarize the data for the identical units. Identical units must be of the same type, process capacity, and installation date. 1. Unit ID: Provide the identification number for the unit. The identification number listed on this form should correspond to the emissions unit identified on the Plant Layout and Process Flow diagrams. 2. Welding Method: Specify the method of welding used at the point of the process defined by each Unit ID. 3. Number of Stations: Specify the number of welding stations covered by each Unit ID. 4. Installation Date: Provide the date on which the unit was installed. If the exact date is not known, provide the month and year of the installation. If the unit has not yet been installed, provide the anticipated installation date. If the unit has been modified or reconstructed since the original installation, include the most recent modification/reconstruction date. 5. Type of Electrode Used: Specify the electrode used by each Unit ID. 6. Maximum Consumption: Provide the maximum consumption of process material in units of pounds per hour (lb/hr). Part B: Flame Cutting Information Part B identifies the flame cutting process. If there are multiple units that are identical in nature, capacity, and use, you may use one row to summarize the data for the identical units. Identical units must be of the same type, process capacity, and installation date. 7. Unit ID: Provide the identification number for the unit. The identification number listed on this form should correspond to the emissions unit identified on the Plant Layout and Process Flow diagrams. 8. Type of Flame Cutting: Specify the type of flame cutting used at the point of the process defined by each Unit ID. 9. Number of Stations: Specify the number of welding stations covered by each Unit ID. American LegalNet, Inc. www.FormsWorkflow.com Indiana Department of Environmental Management Office of Air Quality Air Permit Application Page 2 of 3 PI-07 Instructions 5/2006 10. Installation Date: Provide the date on which the unit was installed. If the exact date is not known, provide the month and year of the installation. If the unit has not yet been installed, provide the anticipated installation date. If the unit has been modified or reconstructed since the original installation, include the most recent modification/reconstruction date. 11. Maximum Metal Thickness Cut: Provide the maximum metal thickness cut in inches (in). 12. Maximum Consumption: Provide the maximum metal cutting rate in units of inches per minute (in/min). Part C: Emission Factors Part C identifies the emission factors used to calculate air emissions from this process. 13. Process / Unit ID: Identify the process and include the identification number for the unit, if applicable. 14. Air Pollutant: For each process identified, list each air pollutant emitted to the atmosphere during normal operation. If there are multiple pollutants for an process, use a new row for each pollutant. 15. Emission Factor: Provide the relevant emission factor including the appropriate units (e.g., lb/units, lbs/ton, lbs/gal, lbs/cf, etc.). 16. Source of Emission Factor: Provide the source of the emission factors. Common sources include AP-42, stack test data, engineering analysis. The United States Environmental Protection Agency (U.S. EPA) has developed a Clearinghouse for Inventories & Emission Factors containing AP-42 and other emission factors. Appendix A of AP-42 lists several common conversion factors that may be needed to calculate potential to emit. Part D: Emission Controls and Limitations Part D identifies control technology, control techniques, or other process limitations that impact air emissions. 17. Add-On Control Technology: Identify all control technologies used for this process, if applicable. A Control Equipment (CE) application form will need to be completed for each control device used, and a summary of control equipment should be submitted using form CE-01. 18. Control Techniques: Identify all control techniques used for this process. 19. Process Limitations / Additional Information: Use the space provided to identify any acceptable process limitations or to provide additional information. An example of an acceptable process limitation would be taking a limit on raw material usage. Such a limit would require an additional record keeping and reporting requirements to be enforceable. For some limitations, performance testing may also be required. Any future change to the established limit will require a permit modification. Part E: Federal Rule Applicability Part E identifies any federal rules that apply to the process. 20. Is a New Source Performance Standard (NSPS) applicable to this source? Specify whether a New Source Performance Standard (NSPS) is applicable to the process unit(s). If a New Source Performance Standard (NSPS) applies, list the rule citation and title in the space provided and submit a FED-01 form to identify the applicable portions of the rule. 21. Is a National Emission Standard for Hazardous Air Pollutants (NESHAP) applicable to this source? Specify whether a National Emission Standard for Hazardous Air Pollutants (NESHAP) is applicable to the process unit(s). If a National Emission Standard for Hazardous Air Pollutants (NESHAP) applies, list the rule citation and title American LegalNet, Inc. www.FormsWorkflow.com Indiana Department of Enviro
Link/Embed this Document
URL
Embed


Popular Searches

  1. JUDGMENT
  2. answer
  3. default judgment
  4. certificate of service
  5. child support
  6. answer to complaint
  7. writ
  8. petition
  9. Affidavit
  10. probate

Bookmark and Share